High-speed rolling gates of the SPEEDROLL SDI series

High-speed roller doors of the SPEEDROLL SDI series are designed for installation on internal openings of premises for any purpose (industrial, warehouse, retail, etc.) in order to isolate and preserve the microclimate.

Application:

Warehouse complexes. Industrial premises

Order with installation

Advantages

High speed gate

High opening speed — up to 2.5 m/s.

Possibility of automation

Reliable automation of our own production.

Additional options

Possibility of installing various additional equipment: photocells, key buttons, drive and rack heating systems, etc.

Frost resistance

Stable operation at significant negative temperatures.

High speed gate

High opening speed — up to 2.5 m/s.

Possibility of automation

Reliable automation of our own production.

Additional options

Possibility of installing various additional equipment: photocells, key buttons, drive and rack heating systems, etc.

Frost resistance

Stable operation at significant negative temperatures.

Design

Surface type

Frame colors

Canvas colors

Doors frame – zinc-coated steel, unpainted

Doors frame – ASIS 304 stainless steel

RAL 9010 Pure white

RAL 5002 Ultramarine blue

RAL 6026 Opal green

RAL 9006 White aluminium

RAL 1003 Signal yellow

RAL 3002 Carmine red

RAL 2004 Pure orange

RAL 9010 Pure white

RAL 5002 Ultramarine blue

RAL 6026 Opal green

RAL 9006 White aluminium

RAL 1003 Signal yellow

RAL 3002 Carmine red

RAL 2004 Pure orange

Equipment

Standard

Optional

Tracks and track covers made of zinc-coated steel

Zinc-coated shaft, diameter 90/130 mm

Guide rails — extruded polyethylene

Door curtain — nontransparent reinforced PVC with density of 900–1 200 g/sqm

Control unit — painted steel body 300 х 400 х 150 mm; protection class — IP54; with frequency converter

Photocells are installed at 500 mm above the floor level, and at the top of side tracks to detect incorrect unwinding of the curtain

Tracks and track covers made of stainless steel AISI304, AISI316

Control unit body made of stainless steel AISI304

Heating of the drive and tracks

If the sensitive lower edge touches an obstruction when the door is closing, then a signal is transmitted to the control unit to open the door. In case of power outage the door opens automatically with a counterweight

Technical description

Size Table

Construction

Standard Construction

Specifications

Operating Conditions

Packaging

Parameters

Value

Opening width, mm

1,200–5,700

Opening height, mm

1,800–5,800

Headroom, mm

From 450

Sideroom clearance, mm

From 225

Electric drive
Shaft
Shaft box
Gate leaf
Transparent insert (window/panel)
Stand
Guide for moving the web
Bottom edge of the canvas
Photocell
Control unit
Counterbalance

Drive on the side.

Symbol, parameter name	Calculation formula
H, mm Opening height	1,600–5,700
B, mm Opening width	1,800–5,800

Front drive.

Symbol, parameter name	Calculation formula
H, mm Opening height	1,600–5,700
B, mm Opening width	1,800–5,800

Parameter	Value	Notes
Wind load, Pa	CLASS1 (up to 82)	For gates 6,000 × 6,000 mm
Wind load, Pa	CLASS2 (up to 90)	For gates 5,000 × 5,000 mm
Opening speed, m/s	2.0	Gates up to 3,000 × 3,000 mm
Opening speed, m/s	1.5	Gates up to 5,000 × 5,000 mm
Opening speed, m/s	1,0	Gates up to 6,000 × 6,000 mm
Closing speed, m/s	0.5
Operating temperature range, °С	-30…+50	When using the rack and drive heating system; when operating in a temperature range of -16…-30 °C, the gate design does not have reinforcement on the leaf, and transparent sections cannot be installed; "Security Profile" option is not available
Power, W	1,500
IP protection class	54	End positions are tracked by encoder
Supply voltage, V	220 V / 50 Hz	Single phase
Supply voltage, V	380 V / 50 Hz	Three-phase
Number of cycles	1,500,000	Depends on operating conditions
Wind load, Pa	CLASS3 (up to 120)	For gates 3,000 × 3,000 mm

Wind load resistance is given for SpeedRoll series doors in the closed position. Gates are not used in places with unstable and high wind loads caused by natural or man-made factors, such as: buildings located on sea coasts or in the mountains; multi-level heated underground parking lots with multiple entrances and exits; production facilities with powerful supply and exhaust ventilation; in buildings of complex configuration with many gate openings, where strong drafts may occur. If one or more of the above factors are present, it is recommended to use a SpeedFold series door or a HSSD series spiral door.

To ensure reliable and uninterrupted operation of the gate, it is recommended to carry out regular technical inspection and maintenance.

Manual opening and closing of the gate is done using a crank.

Do not subject the gate to impacts or interfere with its free opening and closing.

Do not allow the PVC sheet guide to get dirty.

It is prohibited to stand in the opening while the gate is opening and closing to avoid injury.

Make sure that there are no foreign objects in the opening when opening and closing the gate.

The self-healing function of the door leaf in the guides is used to operate the gate in emergency conditions, for example, in the event of an unintentional collision with a vehicle, and is not intended to work when the door leaf is deliberately and systematically knocked out of the guides. The functionality of the function is ensured by the ability of the “zipper” installed on the door leaf to come out of the plastic guides. The functionality of the function cannot be ensured in the event of impacts that exceed the strength parameters of the individual components of the web and system elements. For example, in the event of a collision with a road surface at high speed, impacts with sharp objects, impacts on the top of the gate with raised forks of a forklift, etc.

Packing in wood	Packaging features
Contents	Bubble wrap, polystyrene foam, wooden pallet, wooden blocks
Length, mm	Depends on the length of the gate components
Width, mm	640–705
Height, mm	480–730

Additional Information print

All the DoorHan products are loaded with hydraulic crane or fork-lift truck with 2 m long forks. Customer or installer is recommended to use similar equipment. Truck fork should go under the wooden pallet, provided by the customer, and protrude from its other side. When lifting with crane or other lifting equipment use slings of corresponding lifting capacity.

Installation

Mounting Options

Checking Dimensional Details

Overhead installation of high-speed gates.

All measurements are taken indoors. Each value must be measured at least at three points (in extreme positions and in the center).
B – opening width (distance from the left edge to the right edge of the opening).
H – opening height (distance from the floor to the top of the opening).
h – lintel (distance from the top of the opening to the ceiling).
b1/b2 – left/right lateral distance (distance from the corresponding edge of the opening to the obstacle).
When measuring H and B, the largest value is taken as the final size; when measuring h, b1 and b2, the smallest value is taken.

Warranty print

The buyer is provided with a performance guarantee for high-speed rolling gates produced by the DoorHan concern for a period of 1 year for retail and for a period of 2 years for dealer orders from the date of purchase.

New Products

DoorHan SERVO drive (220 V).

Design

Surface type

Doors frame – zinc-coated steel, unpainted

Doors frame – ASIS 304 stainless steel

Frame colors

RAL 9010 Pure white

RAL 5002 Ultramarine blue

RAL 6026 Opal green

RAL 9006 White aluminium

RAL 1003 Signal yellow

RAL 3002 Carmine red

RAL 2004 Pure orange

Canvas colors

RAL 9010 Pure white

RAL 5002 Ultramarine blue

RAL 6026 Opal green

RAL 9006 White aluminium

RAL 1003 Signal yellow

RAL 3002 Carmine red

RAL 2004 Pure orange

Equipment

Standard

Tracks and track covers made of zinc-coated steel

Zinc-coated shaft, diameter 90/130 mm

Guide rails — extruded polyethylene

Door curtain — nontransparent reinforced PVC with density of 900–1 200 g/sqm

Control unit — painted steel body 300 х 400 х 150 mm; protection class — IP54; with frequency converter

Photocells are installed at 500 mm above the floor level, and at the top of side tracks to detect incorrect unwinding of the curtain

Optional

Tracks and track covers made of stainless steel AISI304, AISI316

Control unit body made of stainless steel AISI304

Heating of the drive and tracks

Technical description

Size Table

Parameters

Value

Opening width, mm

1,200–5,700

Opening height, mm

1,800–5,800

Headroom, mm

From 450

Sideroom clearance, mm

From 225

Construction

Electric drive
Shaft
Shaft box
Gate leaf
Transparent insert (window/panel)
Stand
Guide for moving the web
Bottom edge of the canvas
Photocell
Control unit
Counterbalance

Standard Construction

Drive on the side.

Symbol, parameter name	Calculation formula
H, mm Opening height	1,600–5,700
B, mm Opening width	1,800–5,800

Front drive.

Symbol, parameter name	Calculation formula
H, mm Opening height	1,600–5,700
B, mm Opening width	1,800–5,800

Specifications

Parameter	Value	Notes
Wind load, Pa	CLASS1 (up to 82)	For gates 6,000 × 6,000 mm
Wind load, Pa	CLASS2 (up to 90)	For gates 5,000 × 5,000 mm
Opening speed, m/s	2.0	Gates up to 3,000 × 3,000 mm
Opening speed, m/s	1.5	Gates up to 5,000 × 5,000 mm
Opening speed, m/s	1,0	Gates up to 6,000 × 6,000 mm
Closing speed, m/s	0.5
Operating temperature range, °С	-30…+50	When using the rack and drive heating system; when operating in a temperature range of -16…-30 °C, the gate design does not have reinforcement on the leaf, and transparent sections cannot be installed; "Security Profile" option is not available
Power, W	1,500
IP protection class	54	End positions are tracked by encoder
Supply voltage, V	220 V / 50 Hz	Single phase
Supply voltage, V	380 V / 50 Hz	Three-phase
Number of cycles	1,500,000	Depends on operating conditions
Wind load, Pa	CLASS3 (up to 120)	For gates 3,000 × 3,000 mm

Operating Conditions

To ensure reliable and uninterrupted operation of the gate, it is recommended to carry out regular technical inspection and maintenance.

Manual opening and closing of the gate is done using a crank.

Do not subject the gate to impacts or interfere with its free opening and closing.

Do not allow the PVC sheet guide to get dirty.

It is prohibited to stand in the opening while the gate is opening and closing to avoid injury.

Make sure that there are no foreign objects in the opening when opening and closing the gate.

Packaging

Packing in wood	Packaging features
Contents	Bubble wrap, polystyrene foam, wooden pallet, wooden blocks
Length, mm	Depends on the length of the gate components
Width, mm	640–705
Height, mm	480–730

Additional Information

Installation

Mounting Options

Overhead installation of high-speed gates.

Checking Dimensional Details

All measurements are taken indoors. Each value must be measured at least at three points (in extreme positions and in the center).
B – opening width (distance from the left edge to the right edge of the opening).
H – opening height (distance from the floor to the top of the opening).
h – lintel (distance from the top of the opening to the ceiling).
b1/b2 – left/right lateral distance (distance from the corresponding edge of the opening to the obstacle).
When measuring H and B, the largest value is taken as the final size; when measuring h, b1 and b2, the smallest value is taken.

Warranty

Checkout

Managers of the company will answer all
questions by phone:

420 474 319 111

CALL BACK